..: iDEX - Innovation for Defence Excellence :..

Challenges DRISHTI

Indigenization of Velocimeter (sensor) used in Tail Rotor Vibration Warning System (TRVWS)

TRVWS (Tail rotor vibration warning system) is used to acquire tail rotor vibrations in axial and radial directions in ALH/LCH and was developed by M/s. Merlinhawk in 2007 and they selected Velocimeters P.No.8866-1 supplied by M/s Honeywell. Accordingly, the TRVWS unit has been configured and tuned for the frequencies of Honeywell velocimeters.

Challenges

Challenge 1 Assistance for performing flight test plan with real time data processing and analysis
Challenge 2 Active Repetitive Noise Reduction Adapter (ARNA) for Helicopter Cockpit and Cabin
Challenge 3 Design and Development of Floatable stretcher (litter)
Challenge 4 Development of Controlled Reception Pattern Array
Challenge 5 Design Development and Creation of a High-Fidelity Digital Twin Software Model for a Gas Turbine Starter Engine
Challenge 6 Graphics Processing Board (GPB) and its Test setup
Challenge 7 Development of Annealed Pyrolytic Graphite (APG) material Heat shunt and chassis for effective thermal performance
Challenge 8 Design Manufacturing of Low Noise Compact Axial Fan
Challenge 9 Augmented Reality (AR) for remote visual assistance and pre-flight check inspection automatic defect detection predictive maintenance tool for Do-228 aircraft
Challenge 10 Development of Permanent Magnet Rotor for 400 W Hydraulic Motor Driven Generator
Challenge 11 Design of Silencer in the ECS distribution system of fighter aircraft
Challenge 12 Development of laser based stealth Signature Management Technology
Challenge 13 Elimination of rivet sinking in aircraft structural components
Challenge 14 Wireless Intercom System
Challenge 15 Noise Reduction in Cockpit and Cabin of Hindustan-228 aircraft
Challenge 16 Setup of Technology for Development of 05 types of Ball Bearings for Airborne application
Challenge 17 Automation of I-level Test bench of Inertial Navigation System (G3INS)
Challenge 18 AI AR assisted comprehensive visual inspection of TPE331-12B engine of HTT-40 trainer aircraft
Challenge 19 Autonomous Robotic fettling equipment for intricate and complex castings using Robotics and non-contact vision measurement systems
Challenge 20 Tracking of location of tools gauges in Aircraft Industry
Challenge 21 Remote assistance using AR (Augmented Reality) and VR (Virtual Reality) in an intranet (LANWAN) environment
Challenge 22 Indigenization of Velocimeter (sensor) used in Tail Rotor Vibration Warning System (TRVWS)
Challenge 23 Indigenization of Static Discharger (sensor) used in Helicopter
Challenge 24 Indigenous Development of Fuel Booster pump for CTHCTK Helicopter
Challenge 25 Indigenous Development of Landing Light for CTHCTK Helicopter
Challenge 26 Two-Channel Hybrid Rotary Joint (WR75 SMA) for Polarization Axis of SATCOM-on-the-Move Antenna Systems
Challenge 27 Ku-Band Solid State Power Amplifier (SSPA) for RF Seeker with inhouse designed GaN based PA device
Challenge 28 Indigenous Multi-Node Electronic Deception System
Challenge 29 High power strip line RF Power combiner - 8 way
Challenge 30 Frequency Difference of Arrival based Direction of Arrival for Radar Signals
Challenge 31 Development of X-band Pressure Tight Radome for radar application
Challenge 32 Development of Smart Battery Management System (BMS) for lithium-ion battery pack
Challenge 33 Development of an embedded solution for real -time image analysis using AI
Challenge 34 1-18GHz Cavity Backed Spiral Antenna with dual circular polarizations for Airborne Application
Challenge 35 Design and development of point 5 to 40 GHz Front End Receiver for Airborne Application
Challenge 36 Design and development of system for recognition and Cyber takeover of hostile drones
Challenge 37 Detection of Hypersonic Missile
Challenge 38 Development of Acoustic sensors to detect the drones
Challenge 39 Digital Identity Verification and Cyber Surveillance
Challenge 40 Ethernet Slip Ring and Rotary Joint Assembly
Challenge 41 Health Monitoring System for Sonar Transducers
Challenge 42 Sonar Performance Modelling Software
Challenge 43 Automatic Weather Station
Challenge 44 Development of indigenous ship design Software
Challenge 45 AI powered Hull-form optimization
Challenge 46 AI-Based Detection and Classification of Protective Coating Defects in Defence Platforms as per AMPP NACE SSPC ISO Standards
Challenge 47 Minimising Deformation in thin plate high strength Steel Ship Structure
Challenge 48 Monitoring workforce working inside a ship under construction to identify 1 Number present at a given point in time 2 Identify anyone trapped inside in an emergency situation to enable faster rescue operation
Challenge 49 Advanced Dock finder Tool for dock scheduling
Challenge 50 AI-Driven Propulsion Shaft Alignment and Real-Time Load Diagnostics for Enhanced Shipbuilding Efficiency
Challenge 51 Development of Graphite Based Wet Multiple Friction Disc for an Automatic Transmission Application OFF-Highway Rear Dump Truck
Challenge 52 Electro Hydraulic Steering control system for BD46W-1 Wheel dozer
Challenge 53 Remote Monitoring control of Water Jet system in water sprinklers
Challenge 54 Design Development of Swing Drive (Swing motor Gear box Spring applied hydraulically released parking brake) suitable for closed loop swing circuit on BE1000-1 Hydraulic Excavator (100-ton class Excavator)
Challenge 55 Design and Development of Hydraulic Motor for BG825 Motor Grader
Challenge 56 Design Development of Steering Valve for BG825 Motor Grader
Challenge 57 Indigenous development of following Engine sensors for Dozer Excavator Grader
Challenge 58 Development of Liner Main Charge for 84 mm HEAT 751 Ammunition
Challenge 59 Manufacturing of seamless steel tube of Grade En-24 of size approx 32mm thick outside dia480mm and length 2500mm or its multiple
Challenge 60 Indigenization of DOW CORNING 3140-MIL-A-46146 RTV COATING IN 90 ML TUBE FORM WITH NOZZLE
Challenge 61 CONNECTOR PIN TO OFAJ DRG NO FS-2802A
Challenge 62 SILICONE (UNISILKON) GREASE TK M 1011 FOR BALLISITIC CAP ASSLY
Challenge 63 WIRE ASSEMBLY NO 1 AS PER DRG NO FS-2905 B (673002905)
Challenge 64 GROUND STAINLESS STEEL ROD TO SPECIFICATION SS EN 10088-3-1 4523A SIZE 12 MM DIA IN STRAIGHT LENGTH OF 2 TO 3 METRES
Challenge 65 Development of Amplifier to Drg No PB2035030-01 for BMP-II Gun Stabilization system
Challenge 66 Development of Rate Gyro for T-90 Gun Stabilization System
Challenge 67 Design and Development of Power Traverse for T-72 Stabilization system
Challenge 68 Design and Development of Automatic Gun loading (Distribution Box KP175-3C) based on Solid-State Control Logic
Challenge 69 Design and Development of Directional Gyro (GPK-59) using latest technology (either fibre optics or laser)
Challenge 70 AI-Based System for Design Change Impact Analysis and Cost Estimation
Challenge 71 AI tool for optimization of design wrt Class rules standards regulations etc and synchronize 3D models with Bill of Material (BOM) to eliminate human errors
Challenge 72 Digital Twin Sync (DTS) Design 3D model is shared with production via tablet etc scanned work is compared by AI to flag deviations and changes are remotely synced by Design
Challenge 73 AI enabled intelligent system for drawing verification system for ensuring revision compliance in production drawings
Challenge 74 Design and manufacture of weight for DP system on ship
Challenge 75 Design and manufacture of Anodes for Bow thrusters on ships
Challenge 76 Design of AI based on tool for verification ship design based
Challenge 77 Concept design of LCM for use of LPDs
Challenge 78 Indigenization of DC-DC Converter Module with EMI Filter
Challenge 79 Indigenization of Multi-Section (Double T) EMI EMC Filter
Challenge 80 Indigenization of Mil-grade Metal Transit Container with automatic pressure release valve
Challenge 81 Indigenization of Long Unified Coarse Studs
Challenge 82 AI-enabled Assessment platform for Technical Scrutiny of document
Challenge 83 Development of AI Based Electrical Design Documentation
Challenge 84 AI Based Optimization of Compartment Layout
Challenge 85 Var crucible cleaning equipment
Challenge 86 Induction furnace lining health monitoring system
Challenge 87 Indigenization of ALUMINIUM MOLYBDENUM TITANIUM master alloy production
Challenge 88 Design Development of Altimeter for Paratrooping and Skydiving
Challenge 89 Design Development of Compass for Paratrooping and Skydiving
Challenge 90 Design and Development of a Proximity Sensor for Paratrooping and Skydiving
Challenge 91 Development of Control Valve used for regulation of fuel supply in Heater Space Oil Gas Burner used by Indian Army Air Force BRO NDRF etc
Challenge 92 Development of non-repeatable MSCN fabric across all possible spectrum
Challenge 93 Improvement of colour fastness properties of Combat Uniform Fabric used by defence forces
Challenge 94 Electric Detonator N8T
Challenge 95 Electric Detonator N8TP
Challenge 96 Electric Detonator 5mm No3
Challenge 97 Development of alternative material to replace TFS (Tritium Fluorescence Source) used in Scales of Sights for continuous illumination at night time
Challenge 98 Induction Gyromotor GMA 4 as per Specification No 0780000000 TU
Challenge 99 Motor DPM-20N3-01 as per OST 160515022-76
Challenge 100 DU-125 Muzzle Angle
Challenge 101 VSIT- 1M Technology Workflow

Challenges CPT

Indigenization of Velocimeter (sensor) used in Tail Rotor Vibration Warning System (TRVWS)

Challenges